Viking Range Corporation111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For product information,call 1-888-VIKING1 (845-4641)or visit th
24”(61.0cm)1”(2.54cm)BetweenUnits35”(88.9cm)36”36”(91.5cm)(91.5 cm)36”(91.5cm)9–5/32”(23.3cm)82–3/4”(210.2cm)min.to84–1/16”(213.5cm)max.20–3/4”(52.7cm
Specifications2124”(61.0cm)1”(2.54cm)Betweenunits35”(88.9cm)35”(88.9cm)36”36”(91.5cm)(91.5 cm)36”36”(91.5cm)(91.5 cm)36”(91.5cm)36”(91.5cm)9–5/32”(23.
79–3/8”(201.6cm)min.tobottomofanti-tipboard80–1/2”(204.6cm)max.tobottomofanti-tipboardOne 2”x 4” mounting board per unit1–1/2” (3.8 cm) x 3–1/2” (8.9
79–3/8”(201.6cm)min.tobottomofanti-tipboard80–1/2”(204.6cm)max.tobottomofanti-tipboardNote: If unit is installed deeper than24” (61.0 cm), then shim b
79–3/8”(201.6cm)min.tobottomofanti-tipboard80–1/2”(204.6cm)max.tobottomofanti-tipboardNote: If unit is installed deeper than24” (61.0 cm), then shim b
Top View1–13/16”(4.6 cm)Space if 24” (61.0 cm)standard cabinetdepth is usedDoor24”(61.0 cm)Standard cabinet depthWall3/4”(1.9 cm)Full end panel1-3/4”(
Top ViewFlush mount cabinet doorsTop ViewOverlapping cabinet doorsDoor24”(61.0cm)Standardcabinetdepth24-3/4”(62.9 cm)Wall3/4”(1.9 cm)Full end panel3/4
3/4”(1.9 cm)End panel1”(2.5 cm)1/4”(0.6 cm)Z-Bracket21-3/4”(55.2 cm)21-3/4”(55.2 cm)24”(61.0 cm)Optional kickplate notchDimensions determined by cabin
3534General InformationWater Supply RequirementsUse only 1/4” (6 mm) copper tubing forwater line. Do Not install copper tubing inarea where temperatur
3712Place unit in front of cutout.Pull the center grille louver upat an angle and pull out.34Using an 8” magnetic nut driver, removethe two 1/4” screw
32Table of Contents IMPORTANT–Please Read and Follow!• Make sure that incoming voltage is the sameas unit rating. An electric rating platespecifying v
3938Remove 4 side screws and remove unit top.Loosen the 4 hinge screws. Adjust door.Retighten 4 hinge screws.Replace unit top. Replace 4 side screws.A
4140Turn on water supply and check for leaks.Lift unit off rollers to desired height and level unit usinga 5/16” head wrench.Note: DO NOT use an elect
Performance Checklist43h Verify cabinet size.h Verify electrical supply and water supply(if applicable).h Install anti-tip device(s) and verify unit i
45Service & RegistrationOnly authorized replacement parts may beused in performing service on the appliance.Do not repair or replace any part of t
IMPORTANT–Please Read and Follow!5IMPORTANT–Please Read and Follow!4A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state
724”(61.0cm)35”(88.9cm)75–15/16”(192.9cm)3–19/32”(9.1cm))36”36”(91.5cm)(91.5 cm)36”(91.5cm)26-1/2”(67.3cm)9–5/32”(23.3cm)82–3/4”(210.2cm)min.to84–1/16
Specifications924”(61.0cm)35”(88.9cm)75–15/16”(192.9cm)3–19/32”(9.1cm)36”36”(91.5cm)(91.5 cm)36”(91.5cm)26–1/2”(67.3cm)9–5/32”(23.3cm)82–3/4”(210.2cm)
Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.Note: Top of unit must be placed firmly under anti-tip board.Anti-Tip LocationFlush M
Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.Note: Top of unit must be placed firmly under anti-tip board.79–3/8”(201.6cm)min.tobo
24”(61.0cm)1”(2.54cm)BetweenUnits35”(88.9cm)36”36”(91.5cm)(91.5 cm)36”(91.5cm)9–5/32”(23.3cm)82–3/4”(210.2cm)min.to84–1/16”(213.5cm)max.20–3/4”(52.7cm
Specifications1724”(61.0cm)1”(2.54cm)Betweenunits35”(88.9cm)35”(88.9cm)36”36”(91.5cm)(91.5 cm)36”(91.5cm)36”36”(91.5cm)(91.5 cm)36”(91.5cm)9–5/32”(23.
Kommentare zu diesen Handbüchern