Viking FDFB5302L Installationsanleitung Seite 1

Viking Range, LLC111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For product information,call 1-888-(845-4641)or visit the Viking Web si

Dimensions 1924”(61.0 cm)1”(2.54 cm)Between Units9–5/32”(23.3 cm)82–3/4”(210.2 cm)min.to84–1/16”(213.5 cm)max.20–3/4”(52.7 cm)23–3/8”(59.4 cm)75–15/16

Specifications 2124”(61.0 cm)1”(2.54 cm)Between units35”(88.9 cm)35”(88.9 cm)36”36”(91.5 cm)(91.5 cm)36”36”(91.5 cm)(91.5 cm)36”(91.5 cm)36”(91.5 cm)9

79–3/8”(201.6 cm) min.to bottom of anti-tip board80–1/2”(204.6 cm) max.to bottom of anti-tip boardOne 2”x 4” mounting board per unit1–1/2” (3.8 cm) x

79–3/8”(201.6 cm) min.to bottom ofanti-tip board80–1/2”(204.6 cm) max.to bottom ofanti-tip boardNote: If unit is installed deeper than24” (61.0 cm), t

79–3/8”(201.6 cm) min.to bottom ofanti-tip board80–1/2”(204.6 cm) max.to bottom ofanti-tip boardNote: If unit is installed deeper than24” (61.0 cm), t

Top View1–13/16”(4.6 cm)Space if 24” (61.0 cm)standard cabinetdepth is usedDoor24”(61.0 cm) Standard cabinet depthWall3/4”(1.9 cm

Top ViewFlush mount cabinet doorsTop ViewOverlapping cabinet doorsDoor24”(61.0 cm)Standard cabinet depth24-3/4”(62.9 cm)Wall3/4”(1.9 cm)Full end panel

3/4”(1.9 cm)End panel1”(2.5 cm)1/4”(0.6 cm)Z-Bracket21-3/4”(55.2 cm)21-3/4”(55.2 cm)24”(61.0 cm)Optional kickplate notchDimensions determined by cabin

3534General InformationWater Supply Requirements(All Freezer)Use only 1/4” (6 mm) copper tubing forwater line. Do Not install copper tubing inarea whe

3712Place unit in front of cutout.Pull the center grille louver up at an angle and pull out.34Using an 8” magnetic nut driver, remove the two 1/4” scr

32Table of Contents IMPORTANT—Please Read and Follow!• Make sure that incoming voltage is the sameas unit rating. An electric rating platespecifying v

3938Remove 4 side screws and remove unit top.Loosen the 4 hinge screws. Adjust door. Retighten 4 hinge screws.Replace unit top. Replace 4 side screws.

4140Turn on water supply and check for leaks.Lift unit off rollers to desired height and level unit usinga 5/16” head wrench.Note: DO NOT use an elect

Performance Checklist43□ Verify cabinet size.□ Verify electrical supply and water supply(if applicable).□ Install anti-tip device(s) and verify uni

45Service & RegistrationOnly authorized replacement parts may beused in performing service on the appliance.Do not repair or replace any part of t

4746

IMPORTANT—Please Read and Follow!5IMPORTANT—Please Read and Follow!4A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state

724”(61.0 cm)35”(88.9 cm)75–15/16”(192.9 cm)3–19/32”(9.1 cm))36”36”(91.5 cm)(91.5 cm)36”(91.5 cm)26-1/2”(67.3 cm)9–5/32”(23.3 cm)82–3/4”(210.2 cm)min.

Specifications 924”(61.0 cm)35”(88.9 cm)75–15/16”(192.9 cm)3–19/32”(9.1 cm)36”36”(91.5 cm)(91.5 cm)36”(91.5 cm)26–1/2”(67.3 cm)9–5/32”(23.3 cm)82–3/4”

Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.Note: Top of unit must be placed firmly under anti-tip board. Anti-Tip LocationFlush

Bottom of anti-tip board is 3–7/8” (9.8 cm) below opening height.Note: Top of unit must be placed firmly under anti-tip board. 79–3/8”(201.6 cm) min.

24”(61.0 cm)1”(2.54 cm)Between Units35”(88.9 cm)36”36”(91.5 cm)(91.5 cm)36”(91.5 cm)9–5/32”(23.3 cm)82–3/4”(210.2 cm)min.to84–1/16”(213.5 cm)max.20–3/

Specifications 1724”(61.0 cm)1”(2.54 cm)Between units35”(88.9 cm)35”(88.9 cm)36”36”(91.5 cm)(91.5 cm)36”(91.5 cm)36”36”(91.5 cm)(91.5 cm)36”(91.5 cm)9