Viking VWH 18" Series Installationsanleitung

5 SeriesProfessional Indoor and Outdoor HoodsInstallation Guide

1010" (25.4 cm)dia. duct locationBA30" W 14-15/16" (37.9 cm)36" W 17-15/16" (45.6 cm)42" W 20-15/16" (53.2 cm)48

1110" (25.4 cm)dia. duct locationABA30" W 14-15/16" (37.9 cm)36" W 17-15/16" (45.6 cm)42" W 20-15/16" (53.2 cm)4

1227"(68.6 cm)A18"(45.7 cm)12"(30.5 cm)6"(15.2 cm)A 36" W 35-7/8" (91.1 cm)48" W 47-7/8" (121.6 cm)60"

1330" min.(76. 2 cm)to36" max.(91.4 cm)36"(91.4 cm)66" min.(167.6 cm)to72" max.(182.9 cm)27"(68.6 cm)DIM « X »+ 4-1/2&qu

1424”(61.0 cm)BA18”(45.7 cm)12”(30.5 cm)to24”(61.0 cm)6”(15.2 cm)A (Duct width)30”W. 12“ (30.5 cm)36”W. 12“ (30.5 cm)42”W. 12“ (30.5 cm)48“W. 18“

1530” min.(76.2 cm)to36” max.(91.4 cm)66” min.(167.6 cm)to72” max.(182.9 cm)36”(91.4 cm)(VCWH/CVCWH Chimney Wall Hoods) Clearance Dimensions

16A48”W. 23-15/16” (60.8 cm)60”W. 29-15/16” (76.0 cm)66”W. 32-15/16” (83.7 cm) C48”W. 18” (45.7 cm)60”W. 24” (61.0 cm)66”W. 24” (61.0 cm) 10” (2

17A48”W. 23-15/16” (60.8 cm)60”W. 29-15/16” (76.0 cm)66”W. 32-15/16” (83.7 cm) C48”W. 18” (45.7 cm)60”W. 24” (61.0 cm)66”W. 24” (61.0 cm) 10” (2

18* A 1,200 CFM interior- or exterior-power ventilator should be used when installed over range/rangetop with gas char-grill. Max ductrun is 50 ft.**

1930” min.(76.2 cm)to36” max.(91.4 cm)66” min.(167.6 cm)to72” max.(182.9 cm)36”(91.4 cm)(VCIH /CVCIHChimney Island Hoods) Clearance Dimensions

2Warnings & Important Information_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _

20A54”W. 26-15/16” (68.4 cm)66”W. 32-15/16” (83.7 cm) C54”W. 18” (45.7 cm)66”W. 24” (61.0 cm) 1-1/8”(2.9 cm)1-1/8”(2.9 cm)10” (25.4 cm) dia.duct l

21A54”W. 26-15/16” (68.4 cm)66”W. 32-15/16” (83.7 cm)C54”W. 18” (45.7 cm)66”W. 24” (61.0 cm) 1-1/8”(2.9 cm)1-1/8”(2.9 cm)10” (25.4 cm) dia.duct lo

22(VBCV Wall Custom Ventilator System 36”, 42”, 48”, & 60”)* A 1,200 CFM interior- or exterior-power ventilator should be used when installed over

23ABCustom HoodCanopy1) Position ventilatorsystem inside of thecustom hood canopyand center it front toback and left to right.2) Bottom mounting hol

2430" min.(76.2 cm)to36" max.(91.4 cm)66" min.(167.6 cm)to72" max.(182.9 cm)36"(91.4 cm)(Custom Hood)(VBCV/CVBCV Wall Custom

251-1/2"(3.81 cm)1"(2.54 cm)5/8"(1.6 cm)21-7/8po(55.8 cm)7/8”(2.2 cm)1-1/2”(3.8 cm)17-1/4”(43.8 cm)11-1/2”(29.2 cm)21-7/8”(55.8 cm)5/8”

265/8" (1.6 cm)DC10" (25.4 cm)dia. duct location5-1/2"(14.0 cm)1200 or 1500 CFM Exterior or In-Line Ventilator Installation48”, 60” W.

27Proper installation of ducting is extremelyimportant to ensure maximum performance fromany ventilation product.• All CFMs are based on tests at 0.1

281Check damper for unrestricted movement, adjust ifnecessary. 23Attach transition to damper. Seal with aluminum tape.Flip hood over and remove electr

29CAUTION: If not using a duct cover, using screwsprovided, make sure top mounting screws are securedinto soffit or cabinet framing. Use additional mo

3NOTE:If installing hood with warming shelf panel, installwarming shelf panel first.IMPORTANT – PLEASE READ AND FOLLOW• Before beginning, please read

3012Remove damper and discard with transition.Turn recirculating unit upside down. Place vent hoodupside down on recirculating unit.Installation (VWH/

31CAUTION: Secure vent hood. Make sure mountingscrews are secured into framing. Use additionalmounting screws and wall anchors, if necessary. 75/16”Nu

32Connect black to black, white to white, and thegreen/bare wire under the green screw.NOTE: Housing wiring must be properly installed forwiring to be

33 1-13/16” (4.6 cm) 1-1/2” x 3/4”(3.8 cm) x ( 1.9 cm)wood strip15/16”Nut driverSlot for Wood strip 25/16”Nut driverMeasure down 1-13/16 (4.6 cm) fro

34 122Measure distance from ceiling to canopy.Slide the duct cover in place and fasten from insidecanopy using the sheet metal screws provided.To inst

35342Place duct cover top inside duct cover base and lower untildesired height is found. Mark height. Use the retainingnuts and bolts to fasten in pla

36Check framing where cutout will be. NOTE: 200 lb. limit.Cut appropriate size hole in ceiling. Either 7” or 10”depending on your specific unit and ve

3745/16”NutDriverAttach canopy to duct cover/soffit. Seal top of hood toduct with aluminum tape.3To install ventillation kitrefer to ventillation kiti

38If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the dealer or

39

4WARNINGTO REDUCE THE RISK OF FIRE,ELECTRICAL SHOCK, OR INJURY TO PERSONSRangehoods must be installed withthe ventilators that are specified ontheir c

Viking Range, LLC111 Front StreetGreenwood, Mississippi 38930 USA(662) 455-1200For product information,call 1-888-(845-4641)or visit our web site at v

521"(53.3 cm)A12"(30.5 cm)12"(30.5 cm)A 24" W 23-7/8" (60.6 cm) 30" W 29-7/8" (76.2 cm)36" W 35-7/8" (

6* NOTE: When installing with a 24” high-shelf,the 27” (68.6 cm) max. dimensions must be used.24" min.(61.0 cm)to27" max.*(68.6 cm)60"

7ABCD18”(4.6 cm)3-7/8”(9.8 cm)3-4”(1.9 cm)7” (17.8 cm) dia.duct locationElectricalhookup1/2”(1.3 cm)4”(10.2 cm)3-1/2”(8.9 cm)A24”W. 23-7/8” (60.6 cm)

824"(61.0 cm)A18"(45.7 cm)12"(30.5 cm)6"(15.2 cm)A 30" W 29-7/8" (76.2 cm)36" W 35-7/8" (91.1 cm)42" W

930” min.(76.2 cm)to36” max.(91.4 cm)66” min.(167.6 cm)to72” max.(182.9 cm)36”(91.4 cm)(VWH/CVWH 18”H. Wall Hoods)Clearance Dimensions